 Uninterruptable Power Supply |
| SENTRY MULTISTANDARD ST 40-80kVA |
ON-LINE double conversion VFI technology guarantees a filtered, stabilized and reliable voltage that is free from all mains interference (overvoltages, frequency variations, voltage drops).
>> Download Datasheet PDF
|
 |
|
| Low consumption |
As well as the on-line operating mode, Sentry Multistandard can operate in:
- Economy Mode
The UPS uses Line Interactive technology: the load is powered from the mains; the energy consumption is reduced with a subsequent improvement in efficiency (98%).
- Smart Active Mode
The UPS automatically selects On Line or Line Interactive operating mode according to the quality of the mains supply, by monitoring the number, frequency and type of disturbances at the mains power input.
- Stand-by-Off (back-up unit)
With the mains available the UPS is normally not powered and consequently the power consumption is almost zero. Only when the mains fails or falls outside a preset range, does the inverter take over in 200 ms using power from the batteries. This operating mode is suitable for Emergency Escape Lighting (CPSS - Central Power Supply System) as per standard EN 50171.
These modes can be programmed to suit the requirements of the user and the load to be powered.
|
|
Expandability |
The units can be connected in parallel up to 8 units to increase power availability or redundancy. The single module or the system can be expanded at any time following the power demand without any influence on the initial investment. Thanks to the peculiarity of the ÅgHot System ExpansionÅh feature, the additional unit can be connected in parallel while the other units are on-line and supplying regular power to the load. The new UPS is on-line and will receive the updated information automatically. |
| High reliability |
The digital control of the appliance considerably improves its reliability, since a reduction in electronic components lowers the likelihood of breakdowns. The parallel connection of the UPS up to 8 units exponentially increases the reliability of the system. The parallel connection system has 2 levels of redundancy: in the event both redundant cables are lost only the relevant module will be disconnected from the output bus bar, while the other modules supply power to the load.
|
| Operating flexibility |
Sentry Multistandard is a UPS with On- Line double conversion technology that can also operate in Line Interactive mode (Economy Mode). It can handle the two architectures autonomously through the Smart Active function. The Stand-By-Off function can be used to transform the UPS into a back-up unit to supply power for emergency lighting. Sentry Multistandard can also be used as a Frequency Converter, 50/60Hz or vice versa. |
| Maximum battery care |
Temperature is the greatest threat to batteries; for this reason, Sentry Multistandard monitors the temperature of the battery and thereby controls the battery charging voltage. An automatic battery test periodically checks the efficiency of the batteries. The batteries are not used during micro-interruptions (40 ms), since the required energy is drawn from a group of capacitors (BATTERY SAVING). This system extends the life of the batteries. The Sentry Multistandard range also includes deep discharge protection feature. |
|
Maximum safety for personnel |
The back feed protection device prevents any voltage back feed in the upstream distribution board, thus ensuring the safety of the maintenance personnel. |
| Advanced communication |
The unit comes with EPIÅfs Watch & Save software as a standard feature. The software displays the most important information such as the input and output voltage, the load applied, the remaining back-up time, etc., in the form of bar graphs. It is able to provide information even in the event of a failure, to support the fault diagnostics. Watch & Save software can be used to program the automatic shutdown of all open systems in the event of a prolonged black out.
The UPS also contains the following hardware interfaces:
- RS232 serial port,
- Dry contacts,
- EPO (Emergency Power Off) contact for UPS shutdown using the remote emergency button.
|
|
Mimic panel |
The mimic panel allows easy and intuitive operation of the UPS. It gives access to the most important parameters: status and alarms, control commands, input, output, battery measurements (power, current, voltage, frequency and temperature) and settings. The Sentry Multistandard diagnostics system includes up to 128 alarms or messages allowing precise and detailed identification of any event. |
|
Low Input Harmonic Distortion |
The Power Factor Correction (PFC), standard on all models, guarantees the input power factor level to 0,95 for any load percentages so that it is ideal in conjunction with Motor Generator or in installations with other sensitive loads. Sentry Multistandard is also available with built-in Active Filter designed to reduce the level of THDi to less than 4% and to increase the input power factor up to 0,99.
Other benefits:
- Advanced technologies: Active Filter is based on the IGBTÅfs Technologies controlled by the Digital Signal Processor (DSP). DSP instantly monitors and controls the input current absorbed by the UPS in order to eliminate the unlike harmonics and maintain the THDi less than 4 %.
- Maximum efficiency: thanks to the Active Filter, Multistandard has low input harmonics even at low loads connected at the output.
- Compact size: no addition footprint is required because the Active Filter is fitted inside the base Multistandard unit
.
- Reduction of the neutral current: less harmonics at the Multistandard input reduces the neutral cable size and consequently the installation costs.
- Maximum reliability: thanks to this design solution any failure of the optional Active Filter has no influence on the power supplied to the load; the only consequence is the increase of current harmonics level rejected to the mains. MAXIMUM RELIABILTY FOR THE LOAD.
|
| Applications |
Servers, Local Area Network (LAN), Data centers, telecommunications, industrial equipment, electro-medical equipment, emergency lighting applications. |
| Technical Data |
| Power VA |
Model |
Output
phases |
Dimensions
WXDXH (mm) |
Weight
(kg) |
| 40000 |
ST 40 |
3 + N |
500x740x1400 |
180 |
| 60000 |
ST 60 |
3 + N |
500x740x1400 |
200 |
| 80000 |
ST 80 |
3 + N |
500x740x1400 |
220 |
|
| SENTRY MULTISTANDARD ST 40-80kVA |
| Model |
ST 40 |
ST 60 |
ST 80 |
| Input Voltage |
400 V+ N three-phase |
| Voltage tolerance |
±20% |
| Frequency |
45÷65 Hz |
| Current distortion |
<4% with Active Filter |
| Power factor |
0.99 with Active Filter |
| Rated voltage |
400 V + N |
| Phases number |
3 + N |
| Voltage tolerance |
±15% (selectable from ±5% to ±25%) |
| Rated frequency |
50 / 60 Hz |
| Frequency tolerance |
±2% (selectable up to ±5%) |
| By-pass |
Static and manual for maintenance |
| Transfer time |
0 ms |
| Batteries number |
48 |
| Type |
Maintenance-free sealed lead-acid |
| Battery blocks |
12V |
| Recharge time |
4 - 8 h |
| Rated power |
40000 VA |
60000 VA |
80000 VA |
| Active power |
32 kW |
48 kW |
64 kW |
| Phases number |
3 + N |
| Waveform |
Sinewave |
| Rated voltage |
380-400-415 V (selectable) |
| Frequency |
50 / 60 Hz selectable |
| Dynamic stability |
±5% |
| Static stability |
±1% |
| Crest factor (Ipeak/Irms) |
3 : 1 |
| Overload |
110% for 5h, 125% for 10', 150% for 1' |
| AC/AC efficiency |
92% in On-Line mode 98% in Economy Mode/Smart Active Mode/Emergency mode |
| Noise |
50÷56 dBA at 1 m. |
| Operating temperature |
0°C / +40°C |
| Relative humidity |
95% non condensing |
| Remote controls |
EPO and bypass |
| Remote signals |
Volt free contacts |
| Standards |
Safety EN 62040-1, EMC IEC 62040-2 and EN 50091-2 lev. A, Directives 73/23, 93/68, 89/336 EEC, EN 62040-3 |
| Protection degree |
IP20 |
| Communication |
Double RS232/C |
| Communication slot |
Double RS232/C + slot for SNMP adapter |
| Colour |
Dark grey RAL 7024 |
|
 |
| Sentry Multistandard with Active Filter (internal view) |
|
Product characteristics may be changed to meet specific customer demands
To find out more, please call one of our consultants on +34 951 972 054 or
email sales@epi-iberia.com |
|
|
